Module ngx_http_log_module

• Example Configuration
• Directives
• access_log
• log_format
• open_log_file_cache

The ngx_http_log_module module writes request logs in the specified format.

Requests are logged in the context of a location where processing ends. It may be different from the original location, if an internal redirect happens during request processing.

Example Configuration

log_format compression '$remote_addr - $remote_user [$time_local] '
                       '"$request" $status $bytes_sent '
                       '"$http_referer" "$http_user_agent" "$gzip_ratio"';

access_log /spool/logs/nginx-access.log compression buffer=32k;

Directives

Sets the path, format, and configuration for a buffered log write. Several logs can be specified on the same level. Logging to syslog can be configured by specifying the “syslog:” prefix in the first parameter. The special value off cancels all access_log directives on the current level. If the format is not specified then the predefined “combined” format is used.

If either the buffer or gzip (1.3.10, 1.2.7) parameter is used, writes to log will be buffered.

The buffer size must not exceed the size of an atomic write to a disk file. For FreeBSD this size is unlimited.

When buffering is enabled, the data will be written to the file:

• if the next log line does not fit into the buffer;
• if the buffered data is older than specified by the flush parameter (1.3.10, 1.2.7);
• when a worker process is re-opening log files or is shutting down.

If the gzip parameter is used, then the buffered data will be compressed before writing to the file. The compression level can be set between 1 (fastest, less compression) and 9 (slowest, best compression). By default, the buffer size is equal to 64K bytes, and the compression level is set to 1. Since the data is compressed in atomic blocks, the log file can be decompressed or read by “zcat” at any time.

Example:

access_log /path/to/log.gz combined gzip flush=5m;

For gzip compression to work, nginx must be built with the zlib library.

The file path can contain variables (0.7.6+), but such logs have some constraints:

• the user whose credentials are used by worker processes should have permissions to create files in a directory with such logs;
• buffered writes do not work;
• the file is opened and closed for each log write. However, since the descriptors of frequently used files can be stored in a cache, writing to the old file can continue during the time specified by the open_log_file_cache directive’s valid parameter
• during each log write the existence of the request’s root directory is checked, and if it does not exist the log is not created. It is thus a good idea to specify both root and access_log on the same level:

  server {
      root       /spool/vhost/data/$host;
      access_log /spool/vhost/logs/$host;
      ...
  

The if parameter (1.7.0) enables conditional logging. A request will not be logged if the condition evaluates to “0” or an empty string. In the following example, the requests with response codes 2xx and 3xx will not be logged:

map $status $loggable {
    ~^[23]  0;
    default 1;
}

access_log /path/to/access.log combined if=$loggable;

Specifies log format.

The escape parameter (1.11.8) allows setting json or default characters escaping in variables, by default, default escaping is used.

The log format can contain common variables, and variables that exist only at the time of a log write:

$bytes_sent

the number of bytes sent to a client

$connection

connection serial number

$connection_requests

the current number of requests made through a connection (1.1.18)

$msec

time in seconds with a milliseconds resolution at the time of the log write

$pipe

“p” if request was pipelined, “.” otherwise

$request_length

request length (including request line, header, and request body)

$request_time

request processing time in seconds with a milliseconds resolution; time elapsed between the first bytes were read from the client and the log write after the last bytes were sent to the client

$status

response status

$time_iso8601

local time in the ISO 8601 standard format

$time_local

local time in the Common Log Format

In the modern nginx versions variables $status (1.3.2, 1.2.2), $bytes_sent (1.3.8, 1.2.5), $connection (1.3.8, 1.2.5), $connection_requests (1.3.8, 1.2.5), $msec (1.3.9, 1.2.6), $request_time (1.3.9, 1.2.6), $pipe (1.3.12, 1.2.7), $request_length (1.3.12, 1.2.7), $time_iso8601 (1.3.12, 1.2.7), and $time_local (1.3.12, 1.2.7) are also available as common variables.

Header lines sent to a client have the prefix “sent_http_”, for example, $sent_http_content_range.

The configuration always includes the predefined “combined” format:

log_format combined '$remote_addr - $remote_user [$time_local] '
                    '"$request" $status $body_bytes_sent '
                    '"$http_referer" "$http_user_agent"';

Defines a cache that stores the file descriptors of frequently used logs whose names contain variables. The directive has the following parameters:

max

sets the maximum number of descriptors in a cache; if the cache becomes full the least recently used (LRU) descriptors are closed

inactive

sets the time after which the cached descriptor is closed if there were no access during this time; by default, 10 seconds

min_uses

sets the minimum number of file uses during the time defined by the inactive parameter to let the descriptor stay open in a cache; by default, 1

valid

sets the time after which it should be checked that the file still exists with the same name; by default, 60 seconds

off

disables caching

Usage example:

open_log_file_cache max=1000 inactive=20s valid=1m min_uses=2;